Jul. 29, 2024
Induction coil design can have a major impact on part quality, process efficiency, and manufacturing costs. How do you know if your coil design is best for your part and process? Here are some induction coil basics and five tips to optimize your design.
TY-induction supply professional and honest service.
The induction coil determines how effectively and efficiently a workpiece is heated. Induction coils are water-cooled conductors made of copper tubing that is readily formed into the shape of the coil for the induction heating process. Induction heating coils do not themselves get hot as water flows through them.
Work coils range in complexity from a simple helical- or solenoid-wound coil (consisting of a number of turns of copper tube wound around a mandrel) to a coil that is precision machined from solid copper and brazed.
Coils transfer energy from the power supply to the workpiece by generating an alternating electromagnetic field due to the alternating current flowing in them. The coil&#;s alternating electromagnetic field (EMF) generates an induced current (eddy current) in the workpiece, which generates heat due to I Squared R losses (core losses).
The current in the workpiece is proportional to the coil&#;s EMF strength. This transfer of energy is known as the transformer effect or eddy current effect.
More about the 5 basics of induction coil design...
Induction coil design has a major impact on process efficiency and final part quality, and the best coil design for your product largely depends on your application. Certain coil designs tend to work best with specific applications, and a less than optimal coil-application pairing can result in slow or irregular heating, higher defect rates, and lower quality products.
Start with understanding where the heat needs to be generated in the part to perform the process, and then design the coil to achieve the heating effect. Similarly, frequency selection will depend on the induction heating application you&#;ll be using for your part.
Before designing your induction coil, consider these three factors along with your induction application:
Part motion relative to coil - Several applications rely on part movement with the help of conveyors, turntables, or robots. A properly designed induction coil incorporates these individual handling requirements without the loss of heating efficiency.
Frequency- Higher frequencies are used for applications like brazing, soldering, annealing or heat treating, where surface heating is desired. Lower frequencies are preferred for applications requiring through-heating of the parts to the core like forging and die heating.
Power-density requirements- Higher power densities are required for short cycle heating applications requiring high temperatures. Higher power densities may also be required to keep the hot zone confined to a small area, reducing the heat affected area.
More coil design guidance...
Coupling is the transfer of energy that occurs in the space between the heating portion of the coil and the workpiece. So, coupling distance is how big that space needs to be to balance efficiency and manufacturing requirements.
If you are looking for more details, kindly visit induction heating system design.
Generally, distance increases with the diameter of the part, typical values being 0.75, 1.25, and 1.75 inches (19, 32 and 44 mm) or billet-stock diameters of approximately 1.5, 4 and 6 inches (38, 102, and 152 mm), respectively.
More about coupling distance...
Magnetic flux tends to concentrate toward the center of the length of a solenoid work coil. This means the heating rate produced in this area is generally greater than that produced toward the ends. Further, if the part being heated is long, conduction and radiation remove heat from
the ends at a greater rate. The coil can be modified to provide better heating uniformity along the part length. The technique of adjusting the coil turns, spacing, or coupling with the workpiece to achieve a uniform heating pattern is sometimes known as &#;characterizing&#; the coil.
6 ways to improve uniformity of heating...
The type and design of the induction coil determines how effectively and efficiently a workpiece is heated. Work coils range in complexity from a simple helical- or solenoid-wound coil (consisting of a number of turns of copper tube wound around a mandrel) to a coil that is precision-machined from solid copper and brazed.
The helical solenoid coil is the most ubiquitous induction coil design. It provides a wide range of heating behaviors since the part or heating area is located within the coil, in the area of greatest magnetic flux. Flux lines in a solenoid coil are concentrated inside the coil, providing the maximum heating rate at that location.
More about efficient solenoid coil design...
Wow. That is one big schematic. Well, you can read about a simple, low-power inverter. If you want the big power you need a competent driver. This driver will lock onto the resonant frequency all by itself. As your metal melts it will stay locked onto the correct frequency without the need for any adjustment.
If you have ever built a simple induction heater with a PLL chip you probably recall tuning the frequency as your metal heats. You would watch the waveform move on the oscilloscope. You would keep changing the clocking frequency to maintain that perfect point. No need to do that anymore.
This circuit uses an Arduino microprocessor (uP) to follow the phase difference between the inverter voltage and the tank capacitor. Using this phase it calculates the the correct frequency using a C algorithm.
I will walk you through the circuit:
The tank capacitor signal comes in on the left to LM. This is a high-speed inverter that converts the signal to a nice, clean square-wave. Got to be clean. This signal is then isolated using the optical isolator, FOD. These isolators are key! This signal goes to the PLL through the PCAin input. This is compared to the inverter signal on PCBin, which drives the inverter from VCOout. The Arduino finely controls the PLL clock using a -bit pulse-width modulated signal. The two-stage RC filter converts the PWM signal into a simple analog voltage that goes in at VCOin.
How does the Arduino know what to do? Magic? A good guess? No. It gets the phase-difference information about PCA and PCB from PC1out. R10 and R11 limit the voltage within 5 voltage for the Arduino, and the two-stage RC filter cleans the signal from any noise. We want spanking clean signals because we don't want to pay more money for expensive mosfets after they blow up from noisy inputs.
For more information, please visit china induction heating for tube and pipe company.
If you are interested in sending in a Guest Blogger Submission,welcome to write for us!
All Comments ( 0 )